QUESTION 1You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.Https://www.gratisexam.com/Which type of SVM needs to be created to complete the installation?

QUESTION 2Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

QUESTION 3You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site. Referring to the exhibit, which steps are required to get an HA cabled system?

QUESTION 4You just installed two nodes into an existing ONTAP cluster. When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.Referring to the exhibit, which statement is true?

QUESTION 5You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.In this scenario, what caused this problem?

QUESTION 6A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated.In this scenario, what is happening?

QUESTION 8You are installing a new 2-node AFF A220 cluster running ONTAP 9.5. The customer would like to use the UTA2 adapters from the first controller to connect to the 10GbE front-end switches. On the second controller, they would like to use the first UTA2 port as a target FC port, and the second as an FC initiator.In this scenario, according to NetApp Best practices, what should your customer do?

QUESTION 9You were asked to install a FAS9000 with two quad-port SAS PCI cards. The SAS PCI cards are installed in slot 9 and slot 1. In preparation for the installation, you are filling out the SAS cabling worksheet.In this scenario, which ports are used for the second stack?

QUESTION 13You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster. How many management IP addresses do you need in this scenario?

QUESTION 14You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol. In this scenario, how many FAS9000 HA pairs would be joined to this cluster?

QUESTION 15After properly cabling the NetApp CN1610 cluster switches, you see that joining the second node to a cluster fails because the node is not able to communicate with the other node.In this scenario, what is causing this problem?

QUESTION 16You are planning the deployment of a new 8-node ONTAP 9.5 cluster. To prepare for the installation, you want to create a custom configuration worksheet with all the information that the customer provided. You also want to use the worksheet to generate CLI commands for your installation.In this scenario, which NetApp tool will help you achieve your goal?

QUESTION 19What is the maximum number of data disks that a RAID-TEC RAID group has?

QUESTION 20You want to create a new intercluster LIF for cross-cluster replication and use the CLI. After you create the nac101_intercluster_lif_icl LIF, you are not able to see the LIF in the list of local intercluster LIFs.Referring to the exhibit, what is the problem?

QUESTION 21You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center. In this scenario, what is the minimum number of spare disks required per node and disk type?