QUESTION 38A customer wants to reduce the disk allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates.In this situation, what is this feature called? | Network-Appliance.pass4sureexam.NS0-182.v2020-08-20.by.orla.47

单选题 QUESTION 2
Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

A、Active IQ

B、Config Advisor

C、NetAppDocs

D、Fusion

查看答案

单选题 QUESTION 8
You are installing a new 2-node AFF A220 cluster running ONTAP 9.5. The customer would like to use the UTA2 adapters from the first controller to connect to the 10GbE front-end switches. On the second controller, they would like to use the first UTA2 port as a target FC port, and the second as an FC initiator.
In this scenario, according to NetApp Best practices, what should your customer do?

A、Change all the UTA2 ports from CNA mode to FC mode.

B、Change all the UTA2 ports to CNA to support both FC and Ethernet.

C、Change the first two ports of each controller to FC and the last two to CNA.

D、Change the UTA2 ports from CNA mode to FC mode on the first controller.

查看答案

单选题 QUESTION 5
You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.
In this scenario, what caused this problem?

A、Breakout cables were used and the second port on the same ASIC became disabled.

B、This is a hardware error and you must open a case with NetApp Support.

C、You must first enable the ports using the network port modify command.

D、You are missing a license to enable those ports.

查看答案

单选题 QUESTION 6
A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated.
In this scenario, what is happening?

A、The failover group is configured incorrectly.

B、The fiber switch is configured incorrectly.

C、There is a faulty SFP.

D、The LIFs that serve the block protocol do not failover.

查看答案

单选题 QUESTION 3
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site. Referring to the exhibit, which steps are required to get an HA cabled system?

A、1 Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4.
2 Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4.
3 Cable the out-of-band ACP.

B、1 Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3.
2 Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.

C、1 Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4.
2 Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4.
3 Cable the out-of-band ACP.

D、1 Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3.
2 Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.

查看答案

单选题 QUESTION 1
You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.
Https://www.gratisexam.com/
Which type of SVM needs to be created to complete the installation?

A、system SVM

B、data SVM

C、admin SVM

D、multitenancy node SVM

查看答案

单选题 QUESTION 4
You just installed two nodes into an existing ONTAP cluster. When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.
Referring to the exhibit, which statement is true?

A、The node-management LIF has to be on e0M for NTP to work.

B、The DNS is not configured for this node.

C、The NTP is adjusting in small increments.

D、No NTP server is configured for this node.

查看答案

单选题 QUESTION 9
You were asked to install a FAS9000 with two quad-port SAS PCI cards. The SAS PCI cards are installed in slot 9 and slot 1. In preparation for the installation, you are filling out the SAS cabling worksheet.
In this scenario, which ports are used for the second stack?

A、9a/1d

B、9c/1a

C、9b/1b

D、9a/1a

查看答案